[7] Phuan, Y. J. (2005).
Fe evaluation of thermal property of mould wall material for investment casting and the effect of layers on the hardness of the casting product [Bachelor, Universiti Teknologi Malaysia]. Johor Bahru, Malaysia.
http://eprints.utm.my/id/eprint/2648/1/750 63.pdf
[8] Melo, M. L. N. M., Rizzo, E. M. S., & Santos, R. G. (2005). Predicting dendrite arm spacing and their effect on microporosity formation in directionally solidified Al-Cu alloy.
Journal of Materials Science,
40(7), 1599-1609.
https://doi.org/10.1007/ s10853-005-0659-y
[9] Jie, W., Chen, Z., Reif, W., & Müller, K. (2003). Superheat treatment of Al-7Si-0.55Mg melt and its influences on the solidification structures and the mechanical properties.
Metallurgical and Materials Transactions A,
34(3), 799-806.
https://do i.org/10.1007/s11661-003-0115-z
[10] Pereira, J. C., Gil, E., Solaberrieta, L., San Sebastián, M., Bilbao, Y., & Rodríguez, P. P. (2020). Comparison of AlSi7Mg0.6 alloy obtained by selective laser melting and investment casting processes: Microstructure and mechanical properties in as-built/as-cast and heat-treated conditions.
Materials Science and Engineering: A,
778, 139124.
https://doi.org/10.1016/j.msea.2020.139124
[12] Wang, M., Song, B., Wei, Q., Zhang, Y., & Shi, Y. (2019). Effects of annealing on the microstructure and mechanical properties of selective laser melted AlSi7Mg alloy.
Materials Science and Engineering: A,
739, 463-472.
https://doi.org/10.1016/j.mse a.2018.10.047
[13] Sathishkumar, N., Premkumar, P., Bruce, A. R., Pravinkumar, K., & Sudharsan, P. (2020). Design and analysis of an impeller of a turbocharger.
International Journal of Research and Review,
7(4), 45-51.
https://www.researchgate.net/profile/Sathishkumar-Natesan2/publ ication/341051085_Design_and_Analysis_of_an_Impeller_of_a_Turbocharger/links/5eaaf4d7299bf18b958a553a/Design-and-Analysis-of-an-Impeller-of-a-Turbocharger. pdf
[14] Feneley, A. J., Pesiridis, A., & Andwari, A. M. (2017). Variable Geometry Turbocharger Technologies for Exhaust Energy Recovery and BoostingâA Review.
Renewable and Sustainable Energy Reviews,
71, 959-975.
https://doi.org/10.1016/j.rser.201612.125
[16] Serrano, J. R., Navarro, R., García-Cuevas, L. M., & Inhestern, L. B. (2018). Turbocharger turbine rotor tip leakage loss and mass flow model valid up to extreme off-design conditions with high blade to jet speed ratio.
Energy,
147, 1299-1310.
https://doi.org/10.1016/j.ener gy.2018.01.083
[17] Abdelmadjid, C., Mohamed, S-A., & Boussad, B. (2013). CFD Analysis of the Volute Geometry Effect on the Turbulent Air Flow through the Turbocharger Compressor.
Energy Procedia,
36, 746-755.
https://doi.org/10.1016/j.egypro.2013.07.087
[19] Kumar, R., Madhu, S., Aravindh, K., Jayakumar, V., Bharathiraja, G., & Muniappan, A. (2020). Casting design and simulation of gating system in rotary adaptor using procast software for defect minimization.
Materials Today: Proceedings,
22, 799-805.
https://doi.org/10.1016/j.matpr.2019.10.156